Zhong Carbon Energy Co., Ltd.

enLanguage

Graphite Petroleum Coke Particle Size Selection Guide: Core Differences And Application Scenarios Of 5-10mm And 1-5mm Particle Sizes

Oct 31, 2025 Leave a message

In the production of high-end carbon products such as graphite electrodes and steelmaking carbon raisers, the particle size selection of graphite petroleum coke directly affects product performance, production efficiency, and cost control. This article compares 5-10mm and 1-5mm graphite petroleum coke, two mainstream particle sizes, providing an in-depth analysis from physical structure and chemical reactions to industrial application scenarios, offering enterprises a scientific selection reference.

 

I. 5-10mm Graphite Petroleum Coke: "Skeleton-Level" Aggregate for High-End Products

1. Structural Strength and Stability: Constructing the "Steel Skeleton" of Products

  • Three-Dimensional Network Support: In products such as high-power graphite electrodes and large crucibles, 5-10mm particles form a rigid skeleton through interlocking, increasing the compressive strength of the product by 20%-30%, and significantly improving its resistance to deformation at high temperatures compared to smaller particle formulations.
  • Controllable Shrinkage: During calcination and graphitization, the shrinkage rate of large particles is 15%-20% lower than that of small particles, allowing product dimensional tolerances to be controlled within ±0.5%, reducing scrap rates.

2. Electrical and Thermal Conductivity: Creating an Efficient "Energy Transfer Channel"

  • Long-Range Conductive Network: The graphite crystals inside large particles are more completely arranged, resulting in longer electron conduction paths, increasing electrode conductivity by 10%-15%, and reducing electrode consumption during steelmaking by 8%-12%.
  • Optimized Contact Resistance: Although the number of particle contact points is reduced, the larger contact area and more uniform pressure distribution of large particles reduce overall contact resistance by approximately 10%, reducing energy loss.

3. Chemical Reaction Kinetics: A "Precise Regulator" of Carbon Addition in Steelmaking

  • Stable Dissolution Characteristics: In molten steel at 1600℃, the dissolution time of 5-10mm carbon raiser is 3-5 minutes, with uniform carbon diffusion and a stable yield of 85%-90%, while the yield of 1-5mm particles fluctuates significantly (65%-80%).
  • Low oxidation loss: The specific surface area of ​​large particles is only 1/3 to 1/2 that of small particles, reducing oxidation loss by 25% at high temperatures, making them particularly suitable for highly oxidizing environments such as oxygen converters.

4. Optimized pore structure: Enhancing the "breathability" and oxidation resistance of products

  • Ordered distribution of macroscopic pores: The interconnected pores with a diameter of 50-200 μm formed by large particles can increase the efficiency of volatile matter removal during graphitization by 30%, reducing the risk of internal cracks.
  • Low specific surface area advantage: The total specific surface area is 40%-50% lower than that of small particles of the same mass, reducing the oxidation rate in air at 800℃ by about 20%, extending the service life of products.

 

II. 1-5mm Graphite Petroleum Coke: The "Balancing Master" in Formulation

1. Core of Density Adjustment: The "Precision Filler" for Filling Skeletal Voids

  • Densification Effect: When used in combination with 5-10mm particles, it can fill 30%-40% of the skeletal voids, increasing the product's bulk density by 5%-8%, reaching 1.6-1.8 g/cm³ (the density can reach 1.8-2.0 g/cm³ when small particles are used alone).
  • Binder Reduction: Through gradation optimization (e.g., 5-10mm:1-5mm: fine powder = 5:3:2), the amount of binders such as coal tar pitch can be reduced by 10%-15%, lowering production costs.

2. Scenario-based Applications: A Key Aggregate for Small-sized Products

  • Rapid Response Needs: In induction furnace steelmaking, the dissolution time of 1-5mm recarburizer is only 1-2 minutes, suitable for short-process smelting.
  • Precision Component Manufacturing: When used in micro-graphite molds and battery anode materials, uniform structures with pore sizes <20μm can be achieved by controlling particle size distribution.

 

III. Selection Decision Matrix: Four Dimensions for Scientifically Matching Production Needs

Comparison Dimensions 5-10mm Graphite Petroleum Coke 1-5mm Graphite Petroleum Coke

Core Functions

Structural support and performance dominance density adjustment, and formula balance
Applicable Products Ultra-high power electrodes, large carbon raisers

small and medium-sized carbon blocks, precision molds

Cost-Effectiveness Lower unit strength cost, but the raw material price is 10%-15% higher High filling efficiency can reduce total raw material consumption by 5%-8%
Process Compatibility Requires matching with large-tonnage molding equipment (≥5000-ton press) Suitable for small and medium-sized presses, with lower molding pressure requirements

 

Future Trends: With the development of "coarse particles + ultrafine powder" composite formulation technology, the proportion of 5-10mm large particles in high-end products has increased from 40% to 60%, becoming a key indicator of performance competition.

 

 Collaborative Selection Creates Maximum Value

5-10mm and 1-5mm graphite petroleum coke are not substitutes, but rather achieve optimal performance through "skeleton-filler" synergy. Enterprises need to formulate gradation schemes based on product specifications (size, precision), process conditions (furnace type, temperature), and performance indicators (strength, conductivity). If necessary, they should optimize the particle ratio through experiments (recommended 5-10mm particle size: 40%-60%, 1-5mm particle size: 20%-30%) to reduce overall costs while ensuring quality.